精品乱码一区内射人妻无码-亚洲中文AⅤ中文字幕在线-免费不卡国产福利在线观看-国产综合无码一区二区色蜜蜜

MAGNEHELIC 進口差壓表 2300-60PA

Series 2000 Magnehelic® Gage

for a versatile low differential pressure gage with a wide choice of 81 models and 27 options to choose from. Using Dwyer’s simple, frictionless Magnehelic® gage movement, it quickly indicates air or noncorrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration, over-pressures and is weatherproof to IP67. Select the
 Also included with the –HA option at no extra cost are a mirrored scale overlay and a 6 point calibration certificate.

Note:
May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.

Service:Air and non-combustible, compatible gases (natural gas option available). Note: May be used with hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.

Wetted Materials:Consult factory.

Housing:Die cast aluminum case and bezel, with acrylic cover, Exterior finish is coated gray to withstａnd 168 hour salt spray corrosion test.

Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM ranges), throughout range at 70°F (21.1°C).

Pressure Limits:-20 in Hg. to 15 psig.† (-0.677 bar to 1.034 bar); MP option: 35 psig (2.41 bar), HP option: 80 psig (5.52 bar).

Enclosure Rating:IP67.

Overpressure:Relief plug opens at approximately 25 psig (1.72 bar), standard gages only. See Overpressure Protection note on Catalog page.

Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) with low temperature option.

Size:4" (101.6 mm) diameter dial face.

Mounting Orientation:Diaphragm in vertical position. Consult factory for other position orientations.

Process Connections:1/8" female NPT duplicate high and low pressure taps - one pair side and one pair back.

Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).

Standard Accessories:Two 1/8" NPT plugs for duplicate pressure taps, two 1/8" pipe thread to rubber tubing adapters and three flush mounting adapterswith screws. (Mounting and snap ring retainer substituted for three adapters in MP & HP gage accessories.)

Agency Approval:Meets the technical requirements of EU Directive 2011/65/EU (RoHS II). Note: -SP models not RoHS approved.

Note: For applications with high cycle rate within gage total pressure rating, next higher rating is recommended. See Options Page.

• ASF
  Adjustable Signal Flag
• HP
  High Pressure Option
• LT
  Low Temperatures to -20°F
• MP
  Med. Pressure Option
• SP
  Setpoint Indicator
• Scale Overlays
  Red, Green, Yellow, Mirrored or Combination, Specify Locations

• Mounting and Orientation
  A single case size is used for most models of Magnehelic® gages. They can be flush or surface mounted with standard hardware supplied. Standard gages are calibrated in the vertical position, and should be used in that position for maximum stated accuracy. Ranges above 17.5 in w.c. may be used at any angle, and should stay within specified accuracy, by simply re-zeroing. Ranges below 17.5 in w.c. should be ordered using the –TA tilt angle option with the angle specified. These characteristics make Magnehelic® gages ideal for both stationary and portable applications. A 4-9/16" hole is required for flush panel mounting. Complete mounting and connection fittings, plus instructions, are furnished with each instrument.

• AHU1
  Furnished with attached surface mounting plate
• AHU2
  Furnished with attached surface mounting plate and including A-481 installer kit (2 plastic static pressure tips and 7´of PVC tubing)
• CB
  Chrome bezel option: A chrome plated aluminum bezel for an aesthetically pleasing finish when mounting on metal surfaces such as control panels.
• FC
  Factory calibration certificate
• NIST
  NIST traceable calibration certificate
• SB
  Stainless steel bezel option: 304 stainless steel electro polished Ra 16 finished bezel
• SS
  Corrosion resistant brushed 304 stainless steel bezel